<< Back to Shop Learn Knives

How to: Make a Snake Knot Lanyard for Your Knife

It’s been a while since we’ve done anything with paracord on the Knife Blog. Since we did a handle wrap in the last tutorial, I thought we’d do a lanyard today. The snake knot is super easy to do once you get started. Honestly the hardest part is just getting it set up, but once you get started, it’s the same simple pattern over and over again. I’m not a paracord expert by any means, so if I can make this lanyard, you definitely can too.
The knife in the pictures is a Fallkniven U2, which is a little slim for this lanyard, but it’s what I had around at the moment. A larger knife would probably be better suited for the snake knot lanyard.


You’ll need:


1. Using your knife, cut the paracord to the right length. If you’re going to attach the lanyard to a knife, one of the pieces of paracord needs to be longer than the other. The lanyard I made was about 6 inches long when it was finished, and I used 5 feet of blue paracord and 6 feed of the camo paracord to make it.
2. Melt the ends of the paracord by waving alighter over them. This will help keep the “guts” in and also make it look a little neater.
3. Start off the lanyard with a double overhand knot like this:
It’s basically just a knot that uses two pieces of paracord rather than one, so think of it that way if you’re not familiar with double overhand knots.
(If you look at the finished product of the lanyard when it’s attached to the knife, you’ll see the double overhand knot has been replaced with a diamond not. We did that after the fact to make the lanyard look even more awesome, but don’t worryabout doing that unless you want to.)

4. Take the piece of paracord on the left and loop it around with the end of the paracord going behind the top of the cord. Make sure the paracord on the right remains completely behind the loop you just made.

5. Then move the paracord on the right around to the front and pull it through the loop you made.

6. Grab the paracord that’s going through the loop. Bring it behindand to the leftof the paracord that’s forming the loop. Bring it up, over, down, and through the loop on the right.
5 6

Pull it tight. You’ll want the beginning of the lanyard to be close to the double overhand knot you made.

The hard part is done! From here on out, it’s easy peasy. Now on to the pattern you’ll be following for the rest of the lanyard.

7. Loosen up the “stitch” that’s on the right. In this case, it’s the camo paracord. Then, take the paracord that comes down and through that stitch (for me it’s the blue one), and bring it around back, up, over, and through that stitch that you just loosened.

Make sure to tighten it.

8. Flip the paracord over. Everything should look the same, but reversed.

9. Do the same thing you just did on the other side. Loosen the last stitch on the right, and pull the paracord on the right (that’s coming down and through that stitch) to the back, up, around, and through the stitch on the right.
Tighten it.

10. Flip it over and repeat. Remember to flip over the paracord after each time that you pull paracord through a stitch. Keep it tight as you go. Pretty soon you’ll have something that looks like this:
14 15
You can stop once the lanyard is as long as you want it to be.

Attaching the Lanyard to Your Knife

I looked around for ways to attach your snake knot lanyard to a knife but had no success, so this is what my husband and I came up with. I’m sure there are other, possibly better, ways to do this, but here’s how we did it.
We used a thin piece of wire and a chopstick for this part, but anything you have lying around that’s similar will work great. We definitely improvised on this.
Summary of what we did
We put the longer piece of paracord through the lanyard hole on our knifeand then pulled it down through the middle of the lanyard. We also pulled theshorter cord (the blue one) as far as we could down and and through the lanyard.
If you already know how to go about this or if you have a better way, have at it! If you would like further instruction, read on.
How to attach thelanyard to your knife
1. “Thread” the longer piece of paracord through the lanyard hole.
2. Use the chopstick to make space down the lanyard for the paracord you’ll be pulling down.
(This picture was taken after we had finished the whole thing, so pay no mind to the fact that our lanyard is completely attached already. The picture is just intended to show where you’re putting the chopstick.)

3. After you’ve made some space down the length of the lanyard, get your wire and use it to bring the longer paracord down the inside of the lanyard. (We ended up trimming the paracord after pulling it most of the way down the length of the lanyard.)

This is a look at this end of paracord after it’s been pulled most of the way through the lanyard. You can see it a little bit because of the way we’re bending the lanyard:

4. Without pulling the second piece of paracord through the lanyard hole, pull it down the inside of the lanyard in the same way you pulled the first piece of paracord through. If it looks like it will be too long, feel free to trim it to a more manageable length first. We only had an inch or two that we pulled inside the lanyard.

You should end up with something like this when you’re done:

The snake knot really isn’t bad once you get started. If you’re a paracord fanatic, or if you’re looking for an easy place to start using paracord, try out the snake knot! It’s easy and it allows you to have paracord handy should you need it.
We’ve got lots of paracord available at Blade HQ. Get some and give your knife some paracord love!

2 thoughts on “How to: Make a Snake Knot Lanyard for Your Knife

Comments are closed.